Tag Archive | "sensors"

CETCI’s Solid State vs Non-dispersive Infrared Refrigerant Gas Sensors


For many refrigeration applications, using solid state sensors will provide an economical and reliable gas detection solution. Solid state sensors are reliable if used in a clean area with very little temperature and humidity changes. Solid State refrigerant sensors should not be used where there are other chemicals or gases present (other than refrigerants), such as alcohol based cleaners, fumes from running engines, fuel storage containers, etc.

Using infrared sensor technology will ensure the highest degree of sensor accuracy if monitoring an area where there are other  contamination gases or multiple refrigerants in the same area. Infrared refrigerant sensors should not be used in locations that have corrosive chemicals such as chlorine, ammonia and other oxidizers that are present, especially if there is a higher humidity level.

Comparison of CETCI’s Solid State Refrigerant Sensors and Infrared Refrigerant Sensors

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Applications for Refrigerant Sensors, Recommendation by Sensor Type

refrigerants-applications

 

 

 

 

 

 

NOTE: Ammonia is commonly used as a refrigerant in very low temperature applications such as food/meat processing, ice making plants and ice arenas. Electrochemical sensors are required to ensure accurate monitoring in Ammonia applications.

For more information about our products, check out our website at www.critical-environment.com or to discuss a tailored gas detection solution for your application, contact us at 1-877-940-8741.

Posted in ApplicationsComments Off on CETCI’s Solid State vs Non-dispersive Infrared Refrigerant Gas Sensors

CETCI’s New 3D Printed Calibration Clip Leaves Both Your Hands Free!


At Critical Environment Technologies Canada Inc, (CETCI), we strive to be innovative, cutting edge and creative in our endeavors to fulfill our customers’ needs. Our latest testament to this is our newly designed calibration clip (or ‘Cal Clip’ as it is called for short). It has been an exciting few months as we have gone through different designs, prototypes, various types of plastics and calibration testing.

Remember the last time you calibrated one of our gas detectors that had a splash guard? The blue or orange calibration adapter cup that you had to hold with one hand over the splash guard while trying to open the gas cylinder with the other, flow gas and keep the cup snug up against the device? And depending on the location of the detector, acrobatics may have been involved, right? Well, those days are gone!

Our engineers have designed a device that easily clips around the splash guard and remains in place by itself, freeing up BOTH your hands to do what they need to do. Perhaps even give a high five to a coworker!

before-now-cal-clip

 

The Cal Clip is made of light, durable ABS/polycarbonate plastic and comes in our signature blue company colour. It is specially designed to allow calibration gas into the sensor vent through a small barb hose fitting attached to standard or Teflon tubing. The barb hose fitting can accommodate two sizes of hose: 1/8” (3.175 mm) ID and 3/16” (4.762 mm) ID. While stored, the tubing can be left attached or removed from the Cal Clip as desired.

The Cal Clip fits around the circular, black splash guard that is factory installed at the time of order on any of our black enclosure gas detectors or self-contained controllers. With the hose barb fitting at the bottom, pointing towards you, simply place the inside edge of the Cal Clip next to the outer edge of the splash guard and gently flex open the top of the other side outwards until it slips and clips around the entire splash guard. To remove, gently open the clip at the top while pulling one of the hooked ends towards yourself and it will slip off. If you pull the device apart too aggressively, overstretching it, the circular formation of the Cal Clip may be compromised. Evidence of this results in whitish bars appearing on the blue plastic (like stretchmarks).

NOTE: Because the Cal Clip is designed to prevent entry or exit of air except via the hose barb fitting, it must be removed from the splash guard during normal operation or else the gas readings will not be accurate.

About Critical Environment Technologies Canada Inc.

Critical Environment Technologies designs and manufacturers indoor air quality and fixed gas detection systems including self-contained systems, controllers and analog and digital transmitters. Applications include commercial HVAC, institutional, municipal and light industrial markets worldwide. Many of these applications are for vehicle exhaust, but areas of specialization include refrigeration applications, food processing plants, manufacturing plants, wastewater treatment plants, fisheries, wineries/breweries, pulp and paper mills, recreational facilities, bakeries, greenhouses, and many more.

For more information about our products, check out our website at www.critical-environment.com or to discuss a tailored gas detection solution for your application, contact us at 1-877-940-8741.

Posted in Accessories, News, ProductsComments Off on CETCI’s New 3D Printed Calibration Clip Leaves Both Your Hands Free!

Gas Sensor Life Expectancy


Sensor Life Expectancy in Air Under Normal Conditions

Gas Sensors have an operational life expectancy, a shelf life for storage and a recommended calibration frequency that is commonly dependent on the type of application and environment. All information listed below is approximate, in air and under normal conditions. If you require more specific information on the sensor in the unit you are servicing, contact CETCI for specifications.

Click here to view the Sensor Life Expectancy Chart

For suggestions on gas detection systems, indoor air quality monitors and calibration, please visit

www.critical-environment.com

Posted in ProductsComments Off on Gas Sensor Life Expectancy


Archives

Gas Detectors

CETCI gas detectors are used to detect many different gases. Some of the most common are Carbon Monoxide, Carbon Dioxide, Nitrogen Dioxide, Nitric Oxide, Ammonia, Chlorine, Ozone, Combustible Gases like Methane and Propane, Oxygen, Refrigerants and more.

IAQ Monitors

The YES Series of IAQ Monitors are essential for those responsible for conducting Indoor Air Quality (IAQ) Investigations. These instruments are specifically designed to measure and record the quality of indoor air in offices, buildings, homes, schools, parking garages, ice rinks, etc.